Здравствуйте, Гость

0 Пользователей и 1 Гость просматривают эту тему.

GOOGLE TRANSLATE
привет (жаль я только говорить по-английски Используя Google translatefor говорим сейчас)

я получил заранее 8gb флэш-диска, которые говорят на 8gb, но на самом деле 4 Гб

об использовании H2testw 1.4 выяснилось, что вспышка только 4 Гб

так что я использовал чип гений он показал это

VID 0011

PID 7788

Чип Производитель: Alcor

Чип Часть-номер: f8308


я также открыл крышку флэш-диска было написано там

вспышка контроллер: fc8908
NAND-память: ничего не написано


так что я скачал этот инструмент: Alcor_FC8908_FCMpTool_v05.00.05

он обнаружил мою вспышку и нажал на кнопку запуска он отформатирован вспышкой, но VID PID были изменены и вспышка не работает должным образом показывает, пожалуйста, вставьте диск в дисковод

Теперь чип гений показывает


PnP Device ID: VID = 058F PID = 1234
Серийный номер: 5 & & & & E4D4C9B 0 & & 5
Редакция: 7,76

Тип устройства: стандартное устройство USB - USB2.0 High-Speed

Чип Производитель: Alcor
Чип Часть-номер: AU6981 ~ AU6985

Продукт Vendor: (N / A)
Модель продукта: (N / A)


Сейчас я получаю эту ошибку, когда я подключить вспышку в Alcor_FC8908_FCMpTool_v05.00.05 30400: неизвестный ID ошибки вспышки [0]: 0x45, 0xD7, 0xD8, 0xC2, 0x76, 0xD5


это beacause PID VID были изменены и чип гений показывает другой контроллер вспышки

оригинальный контроллер вспышки напечатаны на вспышки

вспышка контроллер: fc8908 на флэшку wriiten на черный квадрат

Заранее спасибо за любую помощь


ENGLISH

hello  (sorry i only speak english using google translatefor talking now )

i got a advance 8gb flash drive which say's 8gb  but actually is a 4gb

on using H2testw 1.4 it found out that the flash is only a 4gb

so i used chip genius it showed this

vid 0011   

pid 7788

Chip Vendor: Alcor

Chip Part-Number: f8308


i also opened the flash drive cover it was written in there

flash controller: fc8908
nand memory:  nothing is written


so i downloaded this tool: Alcor_FC8908_FCMpTool_v05.00.05

it detected my flash and clicked on the start button it formatted the flash but vid pid got changed and flash does not work properly shows please insert disk into drive

now chip genius shows 


PnP Device ID: VID = 058F PID = 1234
Serial Number: 5&&E4D4C9B&&0&&5
Revision: 7.76

Device Type: Standard USB device - USB2.0 High-Speed

Chip Vendor: Alcor
Chip Part-Number: AU6981~AU6985

Product Vendor: (N/A)
Product Model: (N/A)


now i get this error when i plug the flash in Alcor_FC8908_FCMpTool_v05.00.05 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5   
Is it beacause the vid pid got changed and chip genius shows a different flash controller orginal flash controller printed on flash is flash controller: fc8908 on flash drive wriiten on black square

thanks in advance for any help
« Последнее редактирование: 05 Ноября 2011, 09:31:01 от only knows english »

Оффлайн nat27

*
  • *****
  • 2854
Re: 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
« Ответ #1 : 04 Ноября 2011, 16:49:41 »
The controller fc8908 is a clone alcor au6989, therefore vid&pid=058F&xxxx is admissible.
Error message 30400: unknown flash error ID [0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5 speaks about that Alcor_FC8908_FCMpTool_v05.00.05 hasn't distinguished the module flash memory.
Try to use other utilities:
AlcorMP(110617) - 11,4Mb.
AlcorMP(110726) - 10,3Mb.
AlcorMP(110618.eD3)  - 8,34Mb. 
FCMPTool(050006.eD3) - 7,22Mb.
FCMPTool(040308) - 9,03Mb.
FCMPTool(040311.MD) - 8,69Mb.
Dr.UFDv1.0.0.14.MD - ALCOR au6981-6998, FlashList au6990 date 10.08.2011(август).
Fixer_v1.0.0.3 - PQI (в т.ч. контроллер ALCOR), date 28.01.2011 WinXP\Vista\7.



« Последнее редактирование: 04 Ноября 2011, 16:59:11 от nat27 »
Re: 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
« Ответ #2 : 05 Ноября 2011, 09:25:29 »
nat27
i have tried all the tools you listed none of them seem to work
i still get the same error message in all the tools
Error message 30400: unknown flash error ID [0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5

i don't know why i am getting this error first time i tried  Alcor_FC8908_FCMpTool_v05.00.05 the nand flash got detected and the tool formatted the flash drive showing successful and after that i could see the flash in my computer as 4gb but when i tried to format the flash again in windows it showed write protect error and after that i always got the please insert disk into drive error

why is it that the controller could talk and format the nand flash first time but can't detect it now. is it beacause i forgot to reset the vid pid  after the first low level format

additional information on flash hardware says
controller black: square fc8908
4gb single nand flash: ? (nothing is wriiten on the nand flash)

thanks a lot for replying in english and for you reply....
« Последнее редактирование: 05 Ноября 2011, 09:39:36 от only knows english »

Оффлайн nat27

*
  • *****
  • 2854
Re: 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
« Ответ #3 : 05 Ноября 2011, 15:06:10 »
Good afternoon.
USB Flash Drive (UFD) on the controler fc8xxx fakes.
Means for the first time there was a positive result of restoration by means of Alcor_FC8908_FCMpTool_v05.00.05.
Then utility Alcor_FC8908_FCMpTool_v05.00.05 approaches.
Problem in bad components of a UFD or poor-quality assemblage.
Try to connect a UFD only in USB-port on a system payment if before included in the computer panel.
Very often to restore fake UFD it is not possible.
And so.
« Последнее редактирование: 05 Ноября 2011, 15:09:41 от nat27 »
Re: 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
« Ответ #4 : 06 Ноября 2011, 10:01:14 »
thank's for the reply nat27
i have noticed one more thing when i plug the flash in the fcmptool sometimes it shows this error
30400:unknown flash error
ID[0]: 0xC5,0xD7,0xD8,0xC2,0xF6,0xD5

why did the id change after clicking refresh this error come's back
Re: 30400: unknown flash error
ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5

and sometimes i get this error also

30100:no flash in device error
ID[0]: 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF

the controller seems to be working fine... the problem is that i can't seem to find what manufacturer made the nand flash as it is not written on the nand flash. Is there some way i can find out nand flash manufacturer from this id  (0x45,0xD7,0xD8,0xC2,0x76,0xD5 or 0xC5,0xD7,0xD8,0xC2,0xF6,0xD5) so i can assign manual flash and LLF format this flash back

ps i don't think there soldering problem with the nand flash as it was working before i will try reheating the solder with a hot air gun today to see if it will work ...

thank's for you'r help so far man....
Re: 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
« Ответ #5 : 06 Ноября 2011, 10:09:36 »
i know for sure that the nand flash is 4096 mb in capacity but don't know the manufacturer as when the flash was working before i ran ht2test and it showed 4096 ok (this was sold as a 8gb flash drive but actually only 4gb)

Оффлайн nat27

*
  • *****
  • 2854
Re: 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
« Ответ #6 : 06 Ноября 2011, 10:46:29 »
Astable FlashID speaks about hardware problems.
While there are hardware problems is useless to start service utilities.
UFD-fakes make of the rejected components.
It is impossible to guarantee normal work UFD-fakes.
« Последнее редактирование: 06 Ноября 2011, 11:03:59 от nat27 »

Оффлайн Anatolij

*
  • *****
  • 2669
Re: 30400: unknown flash error ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
« Ответ #7 : 06 Ноября 2011, 11:19:26 »
Пропаять бы неплохо.