Форум - FlashBoot.ru
USB Flash Drive => Восстановление USB Flash Drive на контроллерах ALCOR => Тема начата: FurqanHanif от 08 Ноября 2014, 17:03:35
-
What Tool I use For this Usb??? ???
Description: [K:]USB Mass Storage Device(Generic USB Flash Disk)
Device Type: Mass Storage Device
Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 100mA
USB Device ID: VID = 058F PID = 1234
Device Vendor: Alcor Micro
Device Name: Mass Storage Device
Device Revision: 0001
Manufacturer: Generic
Product Model: USB Flash Disk
Product Revision: 7.76
Controller Vendor: Alcor Micro
Controller Part-Number: AU6989SN/AU6989ANL - F/W 0083
Flash ID code: ADDE94DA - Hynix H27UCG8T2ATR - 1CE/Single Channel [MLC-8K] -> Total Capacity = 8GB
Tools on web: .
Possible Flash Part-Number
----------------------------
[1CE]H27UCG8T2ATR x 1 pcs/Channel x 1 Channel
Flash ID mapping table
----------------------------
[Channel 0] [Channel 1]
ADDE94DA74C4 --------
-------- --------
-------- --------
-------- --------
-
Please Someone Help .... :( :(
-
Hi!!!
ADDE94DA - Hynix H27UCG8T2ATR is 20nm 8Kpage.
Should help AlcorMP\FCMPTool with firmware CTL10\DGD_BIN\10_8K_UCG20_xx.BIN
Must take into account the controller code. May suit AlcorMP(121029), AlcorMP(121102), AlcorMP(121226),
Use WinXP, undesirable win7\8 x64.
-
No FCMP Tool Detecting My USb.. :-\
OK So , i Tried AlcorMP Tool and It detected my USb but it Giving me "Bad Block Error " or Flash Disk Parameters Error" So i Mess With Alcor MP Settings , change these Settings and it USB formated Successfully but When i Write My DATA on My USB , Some of data is Got Currupted so i Tested my USB with Flash Drive Tester and it Shows me Many COmparison Error " Error in Data at LBN" , it Looks Like USB not Formated or it's Space Not Sorted Correctly , Please Help... :(
-
Can this flash drive defective. Or the controller needs to be reset. New good flash drive 8GB is cheap.
http://flashboot.ru/forum/index.php?topic=25161.0 - This topic is similar to your memory stick. Utility ALCOR MP_v14.08.12.00 worked correctly. If your flash drive does not help ALCOR MP_v14.08.12.00 it is not the fault of the utility.
-
But all 8GB is usable when it Got Write Protected , So i Think USB is Good.. :-\
And What Settings You recommend For AlcorMP Tool???
i Tried the Below Settings and it give me "Too Many BAd Block Error"..
http://i.imgur.com/MGtqBQv.png
-
But all 8GB is usable when it Got Write Protected , So i Think USB is Good.. :-\
And What Settings You recommend For AlcorMP Tool???
i Tried the Below Settings and it give me "Too Many BAd Block Error"..
http://i.imgur.com/MGtqBQv.png
-
Likely to have serious problems with the flash drive or the equipment(may be controller) is not working properly. Otherwise, most of the utilities ALCOR MP normally handled flash drive. In a previous post I showed that the normal flash drives with similar equipment are no problems with recovery ALCOR MP_v14.08.12.00.
My opinion is that the flash drive is faulty. Any service utilities can not fix hardware errors.
??? Can the controller needs to be reset...
-
OK So, i Have Tried Some Different Settings and Format , Format Successful But Now Me Flash Space is 15GB , So i Again Change Some Settings Like i Change the Scan Level from Fast Scan to Full Scan 1 and ECC to 15 to 7 , so now myFlash Space is becaome 6GB and all GB is usable and Working fine. So now how i get my Actual Flash Drive Whole Space and Make it Usable?? Looks like it Something To Do with Scan Level Settings... ???
And How To Reset a Controller??
-
6GB for a flash drive is very good. If it works then we can stop.
reset controller
http://flashboot.ru/flash_recovery/2012/11/04/usb-test-pin.html
-
Hmmm So it Means i can Only Get 6GB , Their is no Way To get Actual 8GB Space?? Right??
-
the flash drive is a mystery.
utilities AlcorMP also.
-
Hmmm OK ... i Like Playing with Mysteries .. ;D :P
Thanks for The Help... :)