What Tool I use For this Usb??? ???
Description: [K:]USB Mass Storage Device(Generic USB Flash Disk)
Device Type: Mass Storage Device
Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 100mA
USB Device ID: VID = 058F PID = 1234
Device Vendor: Alcor Micro
Device Name: Mass Storage Device
Device Revision: 0001
Manufacturer: Generic
Product Model: USB Flash Disk
Product Revision: 7.76
Controller Vendor: Alcor Micro
Controller Part-Number: AU6989SN/AU6989ANL - F/W 0083
Flash ID code: ADDE94DA - Hynix H27UCG8T2ATR - 1CE/Single Channel [MLC-8K] -> Total Capacity = 8GB
Tools on web: .
Possible Flash Part-Number
----------------------------
[1CE]H27UCG8T2ATR x 1 pcs/Channel x 1 Channel
Flash ID mapping table
----------------------------
[Channel 0] [Channel 1]
ADDE94DA74C4 --------
-------- --------
-------- --------
-------- --------
Please Someone Help .... :( :(
Hi!!!
ADDE94DA - Hynix H27UCG8T2ATR is 20nm 8Kpage.
Should help AlcorMP\FCMPTool with firmware CTL10\DGD_BIN\10_8K_UCG20_xx.BIN
Must take into account the controller code. May suit AlcorMP(121029), AlcorMP(121102), AlcorMP(121226),
Use WinXP, undesirable win7\8 x64.
No FCMP Tool Detecting My USb.. :-\
OK So , i Tried AlcorMP Tool and It detected my USb but it Giving me "Bad Block Error " or Flash Disk Parameters Error" So i Mess With Alcor MP Settings , change these Settings and it USB formated Successfully but When i Write My DATA on My USB , Some of data is Got Currupted so i Tested my USB with Flash Drive Tester and it Shows me Many COmparison Error " Error in Data at LBN" , it Looks Like USB not Formated or it's Space Not Sorted Correctly , Please Help... :(
Can this flash drive defective. Or the controller needs to be reset. New good flash drive 8GB is cheap.
http://flashboot.ru/forum/index.php?topic=25161.0 - This topic is similar to your memory stick. Utility ALCOR MP_v14.08.12.00 worked correctly. If your flash drive does not help ALCOR MP_v14.08.12.00 it is not the fault of the utility.
But all 8GB is usable when it Got Write Protected , So i Think USB is Good.. :-\
And What Settings You recommend For AlcorMP Tool???
i Tried the Below Settings and it give me "Too Many BAd Block Error"..
http://i.imgur.com/MGtqBQv.png
Цитата: FurqanHanif от 10 Ноября 2014, 19:22:28
But all 8GB is usable when it Got Write Protected , So i Think USB is Good.. :-\
And What Settings You recommend For AlcorMP Tool???
i Tried the Below Settings and it give me "Too Many BAd Block Error"..
http://i.imgur.com/MGtqBQv.png
Likely to have serious problems with the flash drive or the equipment(may be controller) is not working properly. Otherwise, most of the utilities ALCOR MP normally handled flash drive. In a previous post I showed that the normal flash drives with similar equipment are no problems with recovery ALCOR MP_v14.08.12.00.
My opinion is that the flash drive is faulty. Any service utilities can not fix hardware errors.
??? Can the controller needs to be reset...
OK So, i Have Tried Some Different Settings and Format , Format Successful But Now Me Flash Space is 15GB , So i Again Change Some Settings Like i Change the Scan Level from Fast Scan to Full Scan 1 and ECC to 15 to 7 , so now myFlash Space is becaome 6GB and all GB is usable and Working fine. So now how i get my Actual Flash Drive Whole Space and Make it Usable?? Looks like it Something To Do with Scan Level Settings... ???
And How To Reset a Controller??
6GB for a flash drive is very good. If it works then we can stop.
reset controller
http://flashboot.ru/flash_recovery/2012/11/04/usb-test-pin.html
Hmmm So it Means i can Only Get 6GB , Their is no Way To get Actual 8GB Space?? Right??
the flash drive is a mystery.
utilities AlcorMP also.
Hmmm OK ... i Like Playing with Mysteries .. ;D :P
Thanks for The Help... :)