Здравствуйте, Гость

0 Пользователей и 1 Гость просматривают эту тему.

Change the settings flash drive
« : 27 Мая 2017, 00:06:17 »
Hello! Can I somehow change the settings of the flash drive, which would be defined in the device manager as a hard disk

hard IDE\DISKST250DM000-1BD141_______________________KC45____\5&22744B69&0&0.0.0


hard IDE\DiskST250DM000-1BD141_______________________KC45____

usb flash USBSTOR\DiskJetFlashTranscend_8GB___1100
Logical drive   : F:\            Capacity:  7.3G
Device ID       : VID = 8564     PID = 1000
Device SN       : AVGGCC79H02R7TPG
Device version  : 1100

Device vendor   : JetFlash
Device model    : Transcend 8GB
Protocol        : USB2.0
Max power       : 300mA

Partition type  : FAT32          Device active   : OK
Aligned state   : 128 KB, Have been Aligned

Controller      : SMI
Controller model: SM3267AB S
Flash Vendor    : Samsung
Score           : 43       (Normal Score >= 30)
Firmware        : ISP 160118-1AB

I tried to flash the serial number with the firmware, but in the system it was still all the same, not like the hard disk

« Последнее редактирование: 27 Мая 2017, 00:09:32 от serejka4902 »
Change the settings flash drive
« Ответ #1 : 24 Сентября 2017, 16:10:49 »
I have a flash drive with broken socket I have a usb2 socket but I dont know the pin out, could some one please point
Change the settings flash drive
« Ответ #2 : 08 Февраля 2018, 12:36:22 »
I have a USB drive connected to my Nas4Free server. What I would like to do is to backup all data to the USB drive in Windows format nightly. Is this possible? Thanks
Change the settings flash drive
« Ответ #3 : 15 Июля 2018, 10:42:41 »

Can someone tell me how I can partition a usb flash drive - windows 7 disk management wont let me and other partition tools say it is not possible to have more than 1 partition

It is a corsair flash voyager 16gb and I want 2 partitions, 1 for PE and 1 for other tools/files

Change the settings flash drive
« Ответ #4 : 06 Декабря 2018, 13:01:00 »
Im working on a USB flash drive that has a little physical damage on the connector, but no other visible problems. It reports to be 0MB or uninitialised and no data can be read from the OS.

Controller Vendor: SMI
Controller Part-Number: SM3267AC - ISP 160128-1AC
Flash ID code: AD3A18A3 - Hynix H27UDG8M2MTR - 2CE/Single Channel TLC-16K -> Total Capacity = 32GB

Its a double sided board with the controller and one NAND on one side, and the other NAND on the other side. They are TSSOP and QFN parts which for me makes reflow work a lot easier than BGA, so I can take them off to read them externally Id have to get a reader for that. But before Im going the hardware route, Im wondering if the SMI controller has some sort of recovery mode or raw-read mode.

There are a number of MPTools from SMI that have debug portions that allow different kinds of access to the NAND, RAM, controller settings etc. but havent spotted a raw-NAND-read option. It does get detected properly including the NAND, so thats good, but Im not sure how to safely check NAND command availability using MPTool as its obviously intended for manufacturing testing and loading of preset images. I tried the udisk creation option which is supposed to create a low-level image for mass production, but that resulted in 32GB of nulls.

There is a bad block counter thats set to 99, but 97 of those are normal reserved bad block entries, code 80, which appears to not refer to actual bad blocks.
There are two entries in the bad block list that refer to something else:

New Bad Block : 2
=== >>>>> ===================================================================================================
New Block Index: 0, Block: 82, Page: 49, ErrorCode: 3
New Block Index: 1, Block: 86, Page: 3D, ErrorCode: 3
=== <<<<< ===================================================================================================

Other than that, the PCB and none of the chips get warm, the LED does light up but doesnt blink probably because there is no normal FTL activity.

I could start with some simple voltage probing to see if maybe some traces have micro fractures, but perhaps someone here knows of other software controlled testing/reading options for the SMI controllers?
Change the settings flash drive
« Ответ #5 : 22 Января 2020, 09:10:00 »
I would allso like to know if this is possible..
Id allso like to be able to remove the buttons on top.

Ive looked at the source, and removing the buttons can be done by using <PARAM NAME = Show Controls VALUE=No> in the HTML code..