so i have 2 sandisk
1-Safe
2-Crashed
Undrstand?

Frist Use Gordag 952 to extract Safe Flash
Install 3.30 and gnd to Flash pin And Install on Matrix Programmer
I say Image it (in some version back up full the safe memory )

and Back up File must Biger Than 7gig

So
Install Crashed Frimware Flsh
Erase All
Flashed from 7.5g file
in after all verifed
and install again to flash resoldring
and click it need format format it
finish.

so take a picture how you Extract it? How You Install and re soldring it?

How You Install 3.3v?

Someone has to do it? Only see you as always

Description: [G:]Запоминающее устройство для USB(SanDisk Cruzer Edge)
Device Type:??Mass Storage Device

Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 200mA

USB Device ID: VID = 0781 PID = 556B
Serial Number: 20043514511D787341B2

Device Vendor: SanDisk
Device Name: Cruzer Edge
Device Revision: 0126

Manufacturer: SanDisk
Product Model: Cruzer Edge
Product Revision: 1.26

Chip Part-Number: Unknown

ПОМОГИТЕ!!! КАКУЮ ПРОГУ НАЛО!!! ПЛИЗ МУЖИКИ

so i tired to upload 50 picture to undrstand you
Frist Speak English
and second you cant
my Frind you just Software User

You Few Time used mpall and other recovery tools
true is you cant

Just Leave it

One Day I Say I Fix 2251 Famly Frimware Crash error Just Use 10Cm Wire

Every people Say you False But to day Support Comany and to many People UsedMy Way

у меня не видит мою флешку sandisk cruzer edge 8gb… в чем причина помогите((((((( ?????????

I show Pcb Pin To Undrstand Controller Cant Frimware By Him Self
I do Not tell any Body Used him
گوساله

Look All Post-All post Find One Thank You Just 1 Thank you
Frozen culture

Yes Also My All Post Is Fake

Use Matrix nand Programmer

If You can Do It .Why Ask Me
If You cant Do It So You cant You Are Not Flash Fixer Just User

i write more then 250 Comment on Every Flash Erorr and i work it,
SO For Teach You

SDTNMMCHSM-008G is 43nm Abl (Like used Toshiba mlc used in ss6690& ps2251-33)
Flash id is =45CE9632

But Install flash pin1,24,34,38 to vcc3.3v
flash pin2,23,25,48 to GND

If Not Flash Id is =0Xaa ,aa,00

Frist You Posted What You Do ???

Your Programmer Detected Nand memory Id Or Not KId!!!

Show You Programmer detect Flash Id ??

And 10 Years I Work In Hardware

So If You Cant Fix Any Thing Do Not considered

— Information:

If We Extract and Date of Flash We Must Frisr Decodeing(Decrepting Data)

But If Install flash To Same Controller We Do Not Need To Any Manipulation

ps2237 havent any Frimware Run White FC2 So I Install memory on 2232 Fromware 1.5.10
Extract Him and Installed On 2237

So Just Read Table Information and Mbr

I sayid After Install Need Format So I losed Data but Mbr Is safe And Format Is Completed

The reckless behavior prompts you ignore my next article.

remember if You in time Use Programmer Teach it By whom?

i have a USB Flash ( Silicion Power 8GB VID = 13FE / PID = 3E00 ),
my Flash has a problem and i try to fix it with some softwares like Low Lewel Format &
Silicon Power Formatter but not successful, i use ( UP 23 Ctool ) and this software
change

Спасибо! +1 к карме

What programmer? What pinout? Your post fake?

а если флешка литая и не разбираеться?

And Use Usb2 Port For Frimware

Save File

open MPALL_F1_EC00_v363_0D.exe

Click Update And Click Start

Do Not Use Restore 3.12 or Other Restore File

Restore Used Old Frimware To Repiar Flash But In Company Installed Bad Frimware
Good Luck

[PenDriveMP]
IC Type=PS2251-03
[Parameter Mark]
Parameter Type=F1_MP_21
[Customize Info]
USB VID=0x13FE
USB PID=0x5200
String Product Name=USB DISK 3.0
[Configuration]
Reset Serial Number=0
[TestItemOption]
Do Preformat Test=1
[Extra]
Mode=3
[Misc]
Volume Label=USB DISK
Burner Erase All=1
[Advance]
FC1=0xff
FC2=0x01
CheckUSBConnectorType=0x22
[Firmware]
ISP=1
Burner File=BN03V101.BIN
Firmware Name=FW03FF01V10053M.BIN

open Folder Mpall 3.63.0d have phison 2251-03 Frimware Files

Open Mp.ini

MPALL v3.63.0D EC00

Спасибо! Удалось спасти все, что было на флешке.

Плиз, отметьте на фото, какие «ноги» замыкать.