Кстати кому может пригодится моя флешка
FLASH VENDOR: Kingston
MODEL: DataTraveler 111
VID: 0951
PID: 1693
CHIP VENDOR: Phison
CONTROLLER:
MEMORY CHIP:
MEMORY SIZE: 32
UTILS: Formatter Silicon Power v.3.7.0.0
Прога которая помогла форматнуть — Formatter Silicon Power v.3.7.0.0 (PS2251) (http://flashboot.ru/files/file/383/)
Первичная проблема — Диск защищен от записи.
Большое спасибо автору!!! раз 8 пытался реанимировать через online recovery,70% и ошибка… На девятый все отлично прошло,100%. Флешка Transcend JF760 USB3.0 32Gb
FMDATA7 =FRIMWARE DATA INPUT OUT PUT BUS
FRIST TEST ALL FUSE IF LAMP IS ON BUT NO BLINKING DO STEP BY STEP MY WAY
SEE THAT PICTURE AND JUST DO IT
++++++++++++++++++++++++++
LOOK THE R9 OF FLASH BOARD ?SEE THAT? THE FUSE AND L1 ARE FUSE MAY BE YOUR FLASH BOARD IS DIFFRIND BUT ALL AU6XX BASED 1 WAY I CHANGE 6690 BY 6686T AND WORKED AND CHANGE AU6697 BY AU6684 AND AU6698AN BY 6686 SO ALL LEGS IS USE 1 WAY FRIST (1)LEGS OF CONTROLER MUST +5 VOLT
AND CHECK THE ((CONTROLLER Heat)) IF SO HEAT CONTROLLER IS DEAD AND YOU MUST CHANGE IT
BUT IF LAMP HAS ON =FUSE IS OK =CONTOLLER IS OK JUST FRIMWARE CRASHED
CONNECT +5 VOLT TO CONTROLER (I EXPLANE IN PICTURE SO EASY )
При работе с программой SM32X_Modifid__By_Davod_Amiraj пишет Initial Param Fail (0F) (FlashID Not Found in ForceFlash.Set). Перед использованием программы я не делал пока что пунт 1, и 2. Сделаю попозже.
hi:
where the flash Id?
For Example ADDE94D2 — Hynix H27UCG8T2MYR [MLC-8K]
may be flash leg has a broken
frist take a picture of your flash memory and i help you to slove that
Open Flash Cover And take one picture of your flash board like this
FLASH VENDOR: Kingston
MODEL: DataTraveler 111
VID: 0951
PID: 1693
CHIP VENDOR: Phison
CONTROLLER:
MEMORY CHIP:
MEMORY SIZE: 32
UTILS: Formatter Silicon Power v.3.7.0.0
Прога которая помогла форматнуть — Formatter Silicon Power v.3.7.0.0 (PS2251) (http://flashboot.ru/files/file/383/)
Первичная проблема — Диск защищен от записи.
Всем удачи!
и можно записать несколько образов(хр,7 и лив сд например), или сделать несколько дисков?
ISNT IT?
FOR EXAMPLE
FRIST I MUST KNOW YOUR MEMORY IS DEAD OR NOT
YOUR MEAN YOUR FLASH HAS «One piece»؟
LOOK THE BLACK WIRE? SO EASY OK?
FRIST TEST ALL FUSE IF LAMP IS ON BUT NO BLINKING DO STEP BY STEP MY WAY
SEE THAT PICTURE AND JUST DO IT
++++++++++++++++++++++++++
LOOK THE R9 OF FLASH BOARD ?SEE THAT? THE FUSE AND L1 ARE FUSE MAY BE YOUR FLASH BOARD IS DIFFRIND BUT ALL AU6XX BASED 1 WAY I CHANGE 6690 BY 6686T AND WORKED AND CHANGE AU6697 BY AU6684 AND AU6698AN BY 6686 SO ALL LEGS IS USE 1 WAY FRIST (1)LEGS OF CONTROLER MUST +5 VOLT
AND CHECK THE ((CONTROLLER Heat)) IF SO HEAT CONTROLLER IS DEAD AND YOU MUST CHANGE IT
BUT IF LAMP HAS ON =FUSE IS OK =CONTOLLER IS OK JUST FRIMWARE CRASHED
CONNECT +5 VOLT TO CONTROLER (I EXPLANE IN PICTURE SO EASY )
На корпусе флешки я нашел вот что за надпись: PD32GH2GRTS. А открыв корпус SM3257EN L.
connect +5 to controller 13th
smi and phison and ite1167b when +5 to 13th cleaned old frimware run step by step
where the flash Id?
For Example ADDE94D2 — Hynix H27UCG8T2MYR [MLC-8K]
may be flash leg has a broken
frist take a picture of your flash memory and i help you to slove that
+5 нужно подкидывать на 49 пин ( FMDATAL7 )?