Alwayse Fuse Plased In +5 Volt And On Board Named «L1»,«F1» Or «R»
ّFrimWare Crashed
IN some Time Fuse Is Safe But After Flash Plug In Computer Not Happing! So We Must Erase The Bad Frimware And RE Frimwared In Alcor Au69XX
Frsit step Connect +5 to Alcor Fromware Cleaned Pin And Insert To Computer After 3 Or 5 Second You Must Cut The Wire And Run MP Tools «For example for Au6986 we Used AlcorMP_AU698x_RT_v1.0.0.14_L0117»
FMDATA7 =FRIMWARE DATA INPUT OUT PUT BUS
FRIST TEST ALL FUSE IF LAMP IS ON BUT NO BLINKING DO STEP BY STEP MY WAY
SEE THAT PICTURE AND JUST DO IT
++++++++++++++++++++++++++
LOOK THE R9 OF FLASH BOARD ?SEE THAT? THE FUSE AND L1 ARE FUSE MAY BE YOUR FLASH BOARD IS DIFFRIND BUT ALL AU6XX BASED 1 WAY I CHANGE 6690 BY 6686T AND WORKED AND CHANGE AU6697 BY AU6684 AND AU6698AN BY 6686 SO ALL LEGS IS USE 1 WAY FRIST (1)LEGS OF CONTROLER MUST +5 VOLT
AND CHECK THE ((CONTROLLER Heat)) IF SO HEAT CONTROLLER IS DEAD AND YOU MUST CHANGE IT
BUT IF LAMP HAS ON =FUSE IS OK =CONTOLLER IS OK JUST FRIMWARE CRASHED
CONNECT +5 VOLT TO CONTROLER (I EXPLANE IN PICTURE SO EASY )
DavodAmirajam, не используй сплошной провод,+5 на ноги микросхем это опасно — большая перегрузка. Используй сопротивление 5к с проводами.
Я включил служебный режим моему AU6984 вот так
Hi Mr Davod
I tried the way you said but no result.
5V pin connecting the controller and connect it to the USB port was this:
Where is the problem?
My flash model is
Sumsung K9GAG08U0D
And Controller is AU6986
Is there a problem with the controller?
Dear vovoka First Take a look Shimitanic and tell me where is the problem
and I always say Just Use 5 Second To Shock Close Input Out put data bus!!! After All thank you i will test your Way
DavodAmirajam, моя флешка работает, спасибо. Я просто хотел сказать, что если добавить в провод сопротивление 5 килоом, то твой способ станет безопасным — не будет перегрузки.
salam
man ye flash transcend V30 8GB daram.ke format nemishe
ehtemalan chipset on chini ast ke ba barname Jet flash online Recavery ke khode site transcend dade nemishe format kard,mikhastam komakam konid ke aya barnamei hast ke beshe in flash ra format kard?
Email:emperatoorsiavash@yahoo.com
mamnon misham esme barname ya khode barname ra baram mail konid age mitonid
ba tashakoor malek
19 комментариев
All Flash Board have a 1 or 2 Fuse _ And Fuse In Electronic Shock My be Crashed
Open the flash cover find the fuse And Replace him By one Piece Thin wire
ّFrimWare Crashed
IN some Time Fuse Is Safe But After Flash Plug In Computer Not Happing! So We Must Erase The Bad Frimware And RE Frimwared In Alcor Au69XX
Frsit step Connect +5 to Alcor Fromware Cleaned Pin And Insert To Computer After 3 Or 5 Second You Must Cut The Wire And Run MP Tools «For example for Au6986 we Used AlcorMP_AU698x_RT_v1.0.0.14_L0117»
+5 нужно подкидывать на 49 пин ( FMDATAL7 )?
FRIST TEST ALL FUSE IF LAMP IS ON BUT NO BLINKING DO STEP BY STEP MY WAY
SEE THAT PICTURE AND JUST DO IT
++++++++++++++++++++++++++
LOOK THE R9 OF FLASH BOARD ?SEE THAT? THE FUSE AND L1 ARE FUSE MAY BE YOUR FLASH BOARD IS DIFFRIND BUT ALL AU6XX BASED 1 WAY I CHANGE 6690 BY 6686T AND WORKED AND CHANGE AU6697 BY AU6684 AND AU6698AN BY 6686 SO ALL LEGS IS USE 1 WAY FRIST (1)LEGS OF CONTROLER MUST +5 VOLT
AND CHECK THE ((CONTROLLER Heat)) IF SO HEAT CONTROLLER IS DEAD AND YOU MUST CHANGE IT
BUT IF LAMP HAS ON =FUSE IS OK =CONTOLLER IS OK JUST FRIMWARE CRASHED
CONNECT +5 VOLT TO CONTROLER (I EXPLANE IN PICTURE SO EASY )
LOOK THE BLACK WIRE? SO EASY OK?
Я включил служебный режим моему AU6984 вот так
I tried the way you said but no result.
5V pin connecting the controller and connect it to the USB port was this:
Where is the problem?
My flash model is
Sumsung K9GAG08U0D
And Controller is AU6986
Is there a problem with the controller?
and I always say Just Use 5 Second To Shock Close Input Out put data bus!!! After All thank you i will test your Way
Davod jan memory hamoon flash ro ba hiter bardashtam va be ek flash ba conteoller au6989 vasl kardam hich moshkeli nadasht.
az trancend e tam e ax beger bezar enja kimaket kinam
moshkel man ba in hast:
Description: [F:]USB Mass Storage Device(Generic USB
Flash Disk)
Device Type: Mass Storage Device
Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 100mA
USB Device ID: VID = 058F PID = 1234
Device Vendor: Alcor Micro
Device Name: Mass Storage Device
Device Revision: 0001
Manufacturer: Generic
Product Model: USB Flash Disk
Product Revision: 7.76
Chip Vendor: Alcor Micro
Chip Part-Number: Unknown(??) — 0xE302 — F/W 5505
Flash ID Code: C5DE9892 — 2CE/Single Channel [TLC] ->
Total Capacity = 16GB
Az che ver mptool astfade konam?
Mamnoon.
I fix it with MP v12.12.14.00 (upantool.com)
Thanx
man ye flash transcend V30 8GB daram.ke format nemishe
ehtemalan chipset on chini ast ke ba barname Jet flash online Recavery ke khode site transcend dade nemishe format kard,mikhastam komakam konid ke aya barnamei hast ke beshe in flash ra format kard?
Email:emperatoorsiavash@yahoo.com
mamnon misham esme barname ya khode barname ra baram mail konid age mitonid
ba tashakoor malek