Помогите, SILICON POWER 32GB USB 3.0

Восстановление флэш
Вся надежда на вас
Volume: I:
Controller: Phison 2303 (2251-03)
Possible Memory Chip(s):
Intel 29F32B08MCMF2
Intel 29F32B08MCMF3
Intel 29F128G08CBEBB
Intel 29F16B08LCMF3
Intel 29F16B08ACMF1
Memory Type: MLC
Flash ID: 8984643C A5
Chip F/W: 01.08.10
Firmware Date: 2013-06-10
MP Ver.: MPALL vFF.FF.FF
VID: 13FE
PID: 0100
Manufacturer:
Product: silicon power
Query Vendor ID:
Query Product ID: silicon power
Query Product Revision: PMAP
Physical Disk Capacity: 31641829376 Bytes
Windows Disk Capacity: 31620923392 Bytes
Internal Tags: 2QYP-SZ24
File System: FAT32
Relative Offset: 4032 KB
USB Version: 3.00 in 2.00 port
Declared Power: 510 mA
ContMeas ID: 1CF2-04-00
Microsoft Windows 10 x64 Build 14393
— www.antspec.com/usbflashinfo/
Program Version: 8.8.0.601
Если флешку очистить Formatter_SiliconPower, то программа завершится не дойдя до конца
потом пытаюсь востановить с помощью SP Recovery Utility, врорде все ок
форматирую в windows и можно записывать, НО
как только флешка вынута из компа, на нее ничего но возможно записать
пишет «снимите защиту от записи»
приходиться заново повторять весь процесс и форматировать
ПОМОГИТЕ!!!
  • avatar
  • 0

19 комментариев

использование программы MPALL_F1_0702_v363_00 в автоматическом режиме не дало результатов
похоже, надо вводить в ручную.
прошу вашей помощи!
Go silicon power site
Download flash recovery

And site give you update tool to update firmware
1.12.10

Or use mpall 3.71 mlc

it did not work
«this PD can't update»
it did not work
before connect to pc

close 2 pin and connect t to computer

after see 2203 pram

leave shorted
and do mp mpall 3.71
OR CONNECT GND + LED LEFT SIDE
FIRST MUST SEE 2203 PRAMM

SECOND DO FIRMWARE
ALSO USE
DriveCom.exe /drive=E /action=SetBootMode

TO SOFTWARE BOOT MODE

YOU MUST FIRST DO BOOT MODE

I SHOW HARDWARE
AND SOFTWARE WAY TO YOU
IF YOU DONT USE RESTORE EXE

UPDATE CAN FIX THAT

BUT YOUR MAINFUCTOR NAME «UFD 3.0»
IS CLEANED

AND UPDATE TOOL CANT DETECT IT
Dear Davod Amirajam, I do not know at what stage what happened, but after launching Mpall 3.71 there was a restart of the laptop and after turning on the flash card has earned. You are really GURU flash drivers, thank you for your attention!
Dear Davod Amirajam, I do not know at what stage what happened, but after launching Mpall 3.71 there was a restart of the laptop and after turning on the flash card has earned. You are really GURU flash drivers, thank you for your attention!
every flash have 2 firmware

boot mode (rome code mode)
nand firmware

you must go to boot mode

have a 2 way

software mode (use drive com)
or connect gnd +led left side

or close controller pin

read my old articles
read only mode

this mean you cant go to boot mode

your flash must first go firmware 1.1.10
i mark red pin

connect by one Piece wire
connect to pc
ofter five second remove wire

and do firmware again
copy this text to mp.ini in mpall folder

[PenDriveMP]
IC Type=PS2251-03
[Parameter Mark]
Parameter Type=F1_MP_21
[Customize Info]
USB VID=0x13FE
USB PID=0x5200
String Product Name=USB DISK 3.0
String Manufacturer Name=usb
Inquiry Version=PMAP
[Configuration]
Reset Serial Number=0
[TestItemOption]
Do Preformat Test=1
[Extra]
Mode=3
[Misc]
Volume Label=USB DISK
Burner Erase All=1
Wafer Erase All=1
set1667=0x00
[Advance]
FC1=0xFF
FC2=0x01
CheckUSBConnectorType=0x22
[Firmware]
ISP=1
Burner File=BN03V114M.BIN
Firmware Name=FW03FF01V10810M.BIN
Thank you very much, everything turned out!!!
your well com

Оставить комментарий

Имя: