Поиск

[FurqanHanif]

What Tool I use For this Usb??? 
Description: [K:]USB Mass Storage Device(Generic USB Flash Disk)
Device Type:  Mass Storage Device

Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 100mA

USB Device ID: VID = 058F PID = 1234

Device Vendor: Alcor Micro
Device Name: Mass Storage Device
Device Revision: 0001

Manufacturer: Generic
Product Model: USB Flash Disk
Product Revision: 7.76

Controller Vendor: Alcor Micro
Controller Part-Number: AU6989SN/AU6989ANL - F/W 0083
Flash ID code:      ADDE94DA - Hynix H27UCG8T2ATR - 1CE/Single Channel [MLC-8K] -> Total Capacity = 8GB

Tools on web: .


Possible Flash Part-Number
----------------------------
[1CE]H27UCG8T2ATR x 1 pcs/Channel x 1 Channel


Flash ID mapping table
----------------------------
[Channel 0]   [Channel 1]
ADDE94DA74C4   --------
--------   --------
--------   --------
--------   --------

[FurqanHanif]

Please Someone Help ....   

[nat27]

Hi!!!

ADDE94DA - Hynix H27UCG8T2ATR is 20nm 8Kpage.
Should help AlcorMP\FCMPTool with firmware CTL10\DGD_BIN\10_8K_UCG20_xx.BIN
Must take into account the controller code. May suit AlcorMP(121029), AlcorMP(121102), AlcorMP(121226),

Use WinXP, undesirable win7\8 x64.

[FurqanHanif]

No FCMP Tool Detecting My USb.. 
OK So , i Tried AlcorMP Tool and It detected my USb but it Giving me "Bad Block Error " or Flash Disk Parameters Error" So i Mess With Alcor MP Settings , change these Settings and it USB formated Successfully but When i Write My DATA on My USB , Some of data is Got Currupted so i Tested my USB with Flash Drive Tester and it Shows me Many COmparison Error " Error in Data at LBN" , it Looks Like USB not Formated or it's Space Not Sorted Correctly , Please Help... 

[nat27]

Can this flash drive defective. Or the controller needs to be reset. New good flash drive 8GB is cheap.

http://flashboot.ru/forum/index.php?topic=25161.0 - This topic is similar to your memory stick. Utility ALCOR MP_v14.08.12.00 worked correctly. If your flash drive does not help ALCOR MP_v14.08.12.00 it is not the fault of the utility.

[FurqanHanif]

But all 8GB is usable when it Got Write Protected , So i Think USB is Good.. 
And What Settings You recommend For AlcorMP Tool??? 
i Tried the Below Settings and it give me "Too Many BAd Block Error"..
http://i.imgur.com/MGtqBQv.png

[FurqanHanif]

But all 8GB is usable when it Got Write Protected , So i Think USB is Good.. 
And What Settings You recommend For AlcorMP Tool??? 
i Tried the Below Settings and it give me "Too Many BAd Block Error"..
http://i.imgur.com/MGtqBQv.png

[nat27]

Likely to have serious problems with the flash drive or the equipment(may be controller) is not working properly. Otherwise, most of the utilities ALCOR MP normally handled flash drive. In a previous post I showed that the normal flash drives with similar equipment are no problems with recovery ALCOR MP_v14.08.12.00.

My opinion is that the flash drive is faulty. Any service utilities can not fix hardware errors.

Can the controller needs to be reset...

[FurqanHanif]

OK So, i Have Tried Some Different Settings and Format , Format Successful But Now Me Flash Space is 15GB , So i Again Change Some Settings Like i Change the Scan Level from Fast Scan to Full Scan 1 and ECC to 15 to 7 , so now myFlash Space is becaome 6GB and all GB is usable and Working fine. So now how i get my Actual Flash Drive Whole Space and Make it Usable?? Looks like it Something To Do with Scan Level Settings... 
And How To Reset a Controller??

[nat27]

6GB for a flash drive is very good. If it works then we can stop.
reset controller
http://flashboot.ru/flash_recovery/2012/11/04/usb-test-pin.html

[FurqanHanif]

Hmmm So it Means i can Only Get 6GB , Their is no Way To get Actual 8GB Space?? Right??

[nat27]

the flash drive is a mystery.
utilities AlcorMP also.

[FurqanHanif]

Hmmm OK ...  i Like Playing with Mysteries ..   
Thanks for The Help...