+1.04
Рейтинг
0.50
Сила

Davod

Восстановление флэш → Test Toggle Nand memory 6
In Toggle Flash We Dont Need Dual Channel TO meke Read Speed To 30

New Jet Flash Used K9ACGD8U0M Tlc Toggle Flash

in 8Gig Read =30 Write =5

In 2Ce Or K9BDGD8U1M Read =30 write =~12

Not Bad So Better Of ED3

I Test Mlc And Tlc Toggle On Sm3257 Ena

REsult

Восстановление флэш → Test Toggle Nand memory 6
Toggle Memory
Восстановление флэш → Test Toggle Nand memory 6
Also Ite 1165_1167_1167b Have A Multi Channel But Ite 1170 Havent Multi Channel

Realy I dont know Why ?I think New Nand 19nm May Be Have A Problem In Multi Channel
Восстановление флэш → Test Toggle Nand memory 6
try AlcorMP(11.02.17.01)
Восстановление флэш → Помогите разлочить Traveling Disk U172P 11
before mp take picture of your flash «controler name must be show „and i help you to fix it
Восстановление флэш → Помогите разлочить Traveling Disk U172P 11
IF YOU CONNECT +5 TO ALCOR PIN(IO7)I SHOW IN THE PICTURE

DEVICE NAME =GENRIC
VID PID=058F 6387

AFTER SEE IN CHIP GNUNE

CUT THE WIRE

AND DO STRAT!

GOOD LUCK
IT IS EASY
Восстановление флэш → Помогите разлочить Traveling Disk U172P 11
BEFORE INSERT TO MY COMPUTER CONNECT 29+30 PIN
TO CONVERT ORGINAL VID AND PID

Восстановление флэш → Помогите разлочить Traveling Disk U172P 11
JUST CLICK START TO REFRIMWARE IT
Восстановление флэш → Помогите разлочить Traveling Disk U172P 11
AlcorMP_AU698x_RT_v1.0.0.14_L0117
Восстановление флэш → Помогите разлочить Traveling Disk U172P 11
ok connect to GND and insert to pc after 5second breake the wire

if you read old my Article See that

2 pin you see is a placed For Led

But We Connect Gnd To Stop Blinking (Swich off Crystal )

And Start up Ed By Frist Frimware of Controler
\

gook luck
Восстановление флэш → Помогите востановить SILICON POWER Touch T03 8GB 8
ok now your flash losed the nand flash

in last information we did not see the nand Flash id

Open Flash cover And Take A picture from Flash board
Восстановление флэш → Помогите востановить SILICON POWER Touch T03 8GB 8
in phison website i didint see about 2268 and 2207 but i think made in china so we must use china tool
for reFrimware it.
Восстановление флэш → Восстановление флэш Silicon Power USB 2.0 [8Gb] 115
Frist check the flash id?

After 2 min lose the flash id? or not

open chipgnune wait for 2 min => your flash id go to fade it to 00 00 00 after few min
Восстановление флэш → Помогите востановить SILICON POWER Touch T03 8GB 8
we need controller model?

if usb3=i think 2251-03
if usb2=2251-67

mpall 3.63c +frimware for ic
Восстановление флэш → Помогите восстановить Емкость Флеш 1
to all my friend if controller is alcor or smi use online recovery

online recovery also lasted frimware and good Aligned flash seeting
Восстановление флэш → SM3257AA не видит bios но видит операционка через раз 2
i dont undrstand your mean but

frist use online recovery to update Frimware
your frimware is old

Second Jetflash Online recovery Change the 500Ma to 200Ma

Note:

Micron And Intel L74 Not Work Well With 500ma
chane in mp to 200ma

— Also If in boot menu you cant see flash

update bios from mainboard website
and enable usb legacy from bios

and write problem in english to some one help you
Восстановление флэш → SM3257AA не видит bios но видит операционка через раз 2
use last online recovery
AlcorMP_AU698x_RT_v1.0.0.14_L0117 is old

your controller is au6989n

so use jetflash online recovery

or AlcorMP_D3eD3_v13.02.01.07
Восстановление флэш → Восстановление флешки 4
i install 2 hinyx mlc 1ce so
i must to close 2+3

in some pcb may be take jumper in other place but we find with datashet of pcb or use on other people Experiences
Восстановление флэш → After Lose Large Capacity 3


in every flash some jumper to Position And Controller must Undrstand How Many Flash Installed on Pcb

If you Dont Do This May be Flash Capacity is small or Bigger Than Real Capacity look That

Восстановление флэш → After Lose Large Capacity 3