to all my friend if controller is alcor or smi use online recovery

online recovery also lasted frimware and good Aligned flash seeting

i dont undrstand your mean but

frist use online recovery to update Frimware
your frimware is old

Second Jetflash Online recovery Change the 500Ma to 200Ma

Note:

Micron And Intel L74 Not Work Well With 500ma
chane in mp to 200ma

— Also If in boot menu you cant see flash

update bios from mainboard website
and enable usb legacy from bios

and write problem in english to some one help you

use last online recovery
AlcorMP_AU698x_RT_v1.0.0.14_L0117 is old

your controller is au6989n

so use jetflash online recovery

or AlcorMP_D3eD3_v13.02.01.07

i install 2 hinyx mlc 1ce so
i must to close 2+3

in some pcb may be take jumper in other place but we find with datashet of pcb or use on other people Experiences

in every flash some jumper to Position And Controller must Undrstand How Many Flash Installed on Pcb

If you Dont Do This May be Flash Capacity is small or Bigger Than Real Capacity look That

soldring in new pcb

and in mp tool check flash id

note:

Pqi ,Silicon Power ,Some kingstone (Ex 32g controller in the flash connctor 2232+4 mlc lga flash)

have a Weak Pcb

so if have a problem white not detect flash id

we must frist of all

open the flash case and check nand flah

in my case after Full Extract nand i see the broken IO

some people think Problem Alwayse is software and Try Mp Tools
but we must Know 50% Have a Hardware problem.

Thank you all

and plase ,Plase

If You not Interests about this or dont like this do not comment here or

Sex ads

after all we have the flash and data

now clean the nan flash broken side and resoldring an new pcb

now me moved and soldring be full definitude

I am not robot but after 30 min install true controller

Запятую уберите в первой ссылке :)

AlcorMP_AU698x_RT_v1.0.0.14_L0117 определил но работать не захотел «Get Chip Number Fail»

Помогите отформатировать флешку Silicon Power 32gb Marver M01. Ноги замкнул, флешку видит и Silicon Power Recovery Tool и Innostor AI Recovery с оф. сайта, но вылетает с ошибкой «Connect device fail! Please re-plug! Error Code:0x01»

Данные из программы ChipGenius v4.00.0029 / Stable
Description: [H:]Запоминающее устройство для USB(Innostor NAND Flash)
Device Type: Mass Storage Device
Protocal Version: USB 2.10 Hint: This device can run faster when plugged to a USB3.0 port
Current Speed: High Speed
Max Current: 200mA
USB Device ID: VID = 1F75 PID = 0916
Device Vendor: Innostor Technology Corp.
Device Name: IS916EN
Device Revision: 0001
Manufacturer: Innostor
Product Model: NAND Flash
Product Revision: 1.00
Controller Vendor: Innostor
Controller Part-Number: IS916EN-A0 — ??ROM??
Flash ID code: 984CA092 — Toshiba — 2CE/Single Channel [SLC] -> Total Capacity = 32GB

народ помогите для этого контролера нет утилит как восстановить флешку
FLASH VENDOR: verbatim
MODEL: store n go
VID: 0BDA
PID: 0119
CHIP VENDOR:
CONTROLLER:
MEMORY CHIP:
MEMORY SIZE: 8
UTILS:

salam.
mitooni ek aks az chip cob bezare.

чуть не забыл мыло Organizer776@мыло(он же майл).ру

Напишите пожалуйста как добавить подобный cd-rom диск на флешку с контроллером 2251-61 т к в настройках программы его нет

سلام دوستان ممنون از توضیحات خوبتون
من در مورد این چیپ کوب راهی به نظرم رسید و تست کردم
چون این چیپ اون دوتا کنتاکت پایین چیپ رو نداشت اومدم
قبل داخل کردن چیپ به کابل، به کنتاکت دوم از سمت راست یه سیم چسباندم
بعد سر دیگه سیم رو به بدنه کابل افزایش طول وصل کردم و بعد کابل رو به پورت کامپیوتر وصل کردم
این بار فلش شناخته شد اما با خطای
Usb not recognized
و در
device manager: vid/cid=0000
چند بار تست کردم
حتی با کنتاکت دوم از سمت چپ هم تست کردم که بی فایده بود
اما الان که میزنم دیگه اصلا شناخته نمیشه
فکر کنم دیگه کاملا سوخته

firmware from kingston
USB Device ID: VID = 0951 PID = 1689
Chip Vendor: Solid State Systems
Chip Part-Number: SSS6697-B7
my mail: ahmeda2sa2008@yahoo.com

بله حسن جان اگه بتونی خیلی ظریف باز کنی اصلا نند توش جدا گانه نصب شده داداش
ولی من که والا کنترلر 64 پین رو راحت میتونم لحیم کنم ازش ترسیدم