+0.62
Рейтинг
0.50
Сила

Davod

Volume: H:
Controller: Phison PS2307
Possible Memory Chip(s):
Toshiba TH58TFG8DDLTA20
Toshiba TH58TFG8DDLTA2D
Toshiba TC58TFG7DDLTA00
Toshiba TC58TFG7DDLTA0D
Memory Type: MLC
Flash ID: 983A9493 7651
Chip F/W: 05.01.10
Firmware Date: 2016-03-16
ID_BLK Ver.: 1.4.3.0
MP Ver.: MPALL v5.3.0B
VID: 13FE
PID: 5500
Manufacturer: PARLAG
Product: USB DISK 3.0
Query Vendor ID: PARLAG
Query Product ID: USB DISK 3.0
Query Product Revision: DL20
Physical Disk Capacity: 31658606592 Bytes
Windows Disk Capacity: 31641862144 Bytes
Internal Tags: 2Q2P-SX9J
File System: FAT32
Relative Offset: 4032 KB
USB Version: 3.00 in 2.00 port
Declared Power: 300 mA
ContMeas ID: 3AA1-24-00
Microsoft Windows 7 SP1 Build 7601
------------------------------------
Technology without spirituality makes our world so ugly
HAVE FUN


EXTRACT 2 NAND HVJ6MFG AND INSTALL ON ALCOR
AND DO JUMPER MOD
PART 3
TRY USE 3D SUPPORT CONTROLER FOR NAND
I FOUND AU6998SN-GTC
IN FEW DAY I WRITE RESULT PLASE WAIT...
PART 2=>NAND NAND IS DOWNRADED TOSHIBA 3D TLC
HV=LOW PE PROGRAM ERAE TIME AND BAD BLOCK TOO MANY
FOR 64GB?? LOW COST PCB? IN USB3?
This is a betrayal
EVEN IS917 HAVE 3.3 VOLT COIL
I CHECK 5 VOLT FUSE AND BETWEEN GND AND VCC MULTIMETER SHOW 640
SO 5VOLT FINE >The problem is not the customer SYSTEM

3.3 VOLT IS GONE
PROBLEM IS PCB Low cost Stupid design
[PenDriveMP]
IC Type=PS2251-07
[Parameter Mark]
Parameter Type=F1_MP_21
[Customize Info]
USB VID=0x0930
USB PID=0x140B
String Product Name=TransMemory
String Manufacturer Name=TOSHIBA
Inquiry Version=PMAP
Special Serial ID=0x0E
[Configuration]
Reset Serial Number=0
Preformat Target Capacity=29526
TestReadWrite=0
CheckTotalCapacity=32768
TestReadWrite Mode=1
Do TLC Treatment=1
Enable system block recovery=1
Enable SLC user data block recovery=1
Enable TLC/MLC user data block recovery=1
Threshold percentage of ECC to recovery block=70
SSC_ON=0
U1U2_ON=1
Force New Algo=1
[TestItemOption]
Do Preformat Test=1
[Extra]
Mode=3
LED Function=0xCC
[Misc]
Volume Label=TOSHIBA
Burner Erase All=1
Wafer Erase All=1
set1667=0x00
[Advance]
FC1=0xFF
FC2=0x01
CheckUSBConnectorType=0x22
KeepUIStatus=1
[Firmware]
ISP=1
Burner File=BN.BIN
Firmware Name=FW55.BIN
[Advanced Configuration]
Timing10B=0x02
ي(
[PenDriveMP]
IC Type=PS2251-07
[Parameter Mark]
Parameter Type=F1_MP_21
[Customize Info]
USB VID=0x0930
USB PID=0x140B
String Product Name=TransMemory
String Manufacturer Name=TOSHIBA
Inquiry Version=PMAP
Special Serial ID=0x0E
[Configuration]
Reset Serial Number=0
Preformat Target Capacity=29526
TestReadWrite=0
CheckTotalCapacity=32768
TestReadWrite Mode=1
Do TLC Treatment=1
Enable system block recovery=1
Enable SLC user data block recovery=1
Enable TLC/MLC user data block recovery=1
Threshold percentage of ECC to recovery block=70
SSC_ON=0
U1U2_ON=1
Force New Algo=1
[TestItemOption]
Do Preformat Test=1
[Extra]
Mode=3
LED Function=0xCC
[Misc]
Volume Label=TOSHIBA
Burner Erase All=1
Wafer Erase All=1
set1667=0x00
[Advance]
FC1=0xFF
FC2=0x01
CheckUSBConnectorType=0x22
KeepUIStatus=1
[Firmware]
ISP=1
Burner File=BN.BIN
Firmware Name=FW10.BIN
[Advanced Configuration]
Timing10B=0x02
ي(
LAST FIRMWARE 15NM TLC 2207 €Aug 22 2017.03:1
USE THIS TOOL
ST-TOOL_9000_v3.7F.92
do mpall 5.3.b for tlc 15nm

or ST-TOOL_9000_v3.7F.92 use gen2 3D FLASH

BUT BEFORE RAPE YOUR FLASH MEMORY.

1=DO MPALL IF EJECT IN FIRMWARE DO MY WAY
2= READ FIDE YOUR FLASH

IF FIDE = 98 3C 98 B3 76 = YOUR FLASH IS 3D TLC
FOR TLC USE ST-TOOL_9000_v3.7F.92

IF FIDE 98 3A 98 A3 USE MPALL 5.3.B

GOOD LOCK