JUST CLICK START TO REFRIMWARE IT

AlcorMP_AU698x_RT_v1.0.0.14_L0117

ok connect to GND and insert to pc after 5second breake the wire

if you read old my Article See that

2 pin you see is a placed For Led

But We Connect Gnd To Stop Blinking (Swich off Crystal )

And Start up Ed By Frist Frimware of Controler
\

gook luck

ok now your flash losed the nand flash

in last information we did not see the nand Flash id

Open Flash cover And Take A picture from Flash board

in phison website i didint see about 2268 and 2207 but i think made in china so we must use china tool
for reFrimware it.

Frist check the flash id?

After 2 min lose the flash id? or not

open chipgnune wait for 2 min => your flash id go to fade it to 00 00 00 after few min

we need controller model?

if usb3=i think 2251-03
if usb2=2251-67

mpall 3.63c +frimware for ic

to all my friend if controller is alcor or smi use online recovery

online recovery also lasted frimware and good Aligned flash seeting

i dont undrstand your mean but

frist use online recovery to update Frimware
your frimware is old

Second Jetflash Online recovery Change the 500Ma to 200Ma

Note:

Micron And Intel L74 Not Work Well With 500ma
chane in mp to 200ma

— Also If in boot menu you cant see flash

update bios from mainboard website
and enable usb legacy from bios

and write problem in english to some one help you

use last online recovery
AlcorMP_AU698x_RT_v1.0.0.14_L0117 is old

your controller is au6989n

so use jetflash online recovery

or AlcorMP_D3eD3_v13.02.01.07

i install 2 hinyx mlc 1ce so
i must to close 2+3

in some pcb may be take jumper in other place but we find with datashet of pcb or use on other people Experiences

in every flash some jumper to Position And Controller must Undrstand How Many Flash Installed on Pcb

If you Dont Do This May be Flash Capacity is small or Bigger Than Real Capacity look That

soldring in new pcb

and in mp tool check flash id

note:

Pqi ,Silicon Power ,Some kingstone (Ex 32g controller in the flash connctor 2232+4 mlc lga flash)

have a Weak Pcb

so if have a problem white not detect flash id

we must frist of all

open the flash case and check nand flah

in my case after Full Extract nand i see the broken IO

some people think Problem Alwayse is software and Try Mp Tools
but we must Know 50% Have a Hardware problem.

Thank you all

and plase ,Plase

If You not Interests about this or dont like this do not comment here or

Sex ads

after all we have the flash and data

now clean the nan flash broken side and resoldring an new pcb

now me moved and soldring be full definitude

I am not robot but after 30 min install true controller

بله حسن جان اگه بتونی خیلی ظریف باز کنی اصلا نند توش جدا گانه نصب شده داداش
ولی من که والا کنترلر 64 پین رو راحت میتونم لحیم کنم ازش ترسیدم

na dada ic intel 100% good gabol nadaram

ba urecurce jadid check kon

to mp full Erase kon

va Voltago az 480m be ===>300 ma tager bedeh

سلام با عرض ارادت خدمت هموطنان

آقا سلیقه شرکتها متفاوته

یعنی چی ؟

یعنی امکان داره

Sm3257ena+tlc
sm3255ae+mlc
ite1167b+mlc

بعدشم ممکنه چند کاناله باشه

رو pcb

استاندارد ما
مموری رو میبینیم

ولی تو فلش پرسی خیلی سخته چون کسی دیتا شیتیشو نداره

من شخصا تو فلش استاندارد مموری رو برمیدارم

میندازم تو کنترلری که همنام خودش باشه بدون هیچ مشکلی دیتاشو در میارم
مثلا

Jetflash=sm3257ena+Sumsung 21 nm tog tlc.

خوب کنترلر سوخته اما نند فلش زندس خوب

یه سیلیکون پاور باز میکنم

sm323257ena+sandisk tlc

مموریشو بر میدارم
مموری جت فلشو میذارم روش
هیتر لحیم کاری بعد دیتاشو بر میدارم به همین ساده گی

— موفق باشین