problem with SMI Factory Driver; please Help!

Hi
I would create cd-rom on ufd SM3257ENAA. I face to a error and ufd couldn't recognize normally. In device manager it detected but had not drive letter. So, I use «SMI Factory Driver» with [VID = 090C PID = 1000]. After that, SMI MPTool could detect it using «Factory Driver and Hub» option. I began to flashing but it still on Testing. I would stop flashing, so i use «quit» button and then un-plug ufd. after re-plug windows detect it with SMI Factory Drive but SMI MPTool hang when I pressing «Scan USB (F5)».
I try on another windows but is same.
There is any way to revival ufd?

———————————————————————————————————
Description: [M:]USB Mass Storage Device(SMI USB DISK)
Device Type: Mass Storage Device

Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 500mA

USB Device ID: VID = 090C PID = 1000

Device Vendor: SMI Corporation
Device Name: USB DISK
Device Revision: 1100

Manufacturer: SMI
Product Model: USB DISK
Product Revision: 1100

Controller Vendor: SMI
Controller Part-Number: SM3257ENAA – ISP 120119-AA-
Flash ID code: 98DE9493 – Toshiba – 1CE/Single Channel [MLC] -> Total Capacity = 8GB

Tools on web: dl.mydigit.net/special/up/smi.html

Possible Flash Part-Number
—————————-
Unknown

Flash ID mapping table
—————————-
[Channel 0] [Channel 1]
98DE9493 ——--
——-- ——--
——-- ——--
——-- ——--
——-- ——--
——-- ——--
——-- ——--
——-- ——--
—————————————————————————————————--

I clean registery and re-plug it. SMI MPTool dont detect it.
ChipGenius report it:
====================================
Description: USB Mass Storage Device

Protocal Version: USB 2.00
Current Speed: Low Speed

USB Device ID: VID = 090C PID = 1000

Device Revision: 1100

Controller Part-Number: Unknown
=====================================

Also install SMI factory driver ( 090C/1000). but SMI MPTool hanged when I press «Scan USB » button.
Now ChipGenius report it:
=====================================
Description: SMI Factory Driver(DataKey USB Disk)
Device Type: Mass Storage Device

Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 500mA

USB Device ID: VID = 090C PID = 1000
Serial Number: AA00000000010564

Device Vendor: DataKey
Device Name: USB Disk
Device Revision: 1100

Controller Part-Number: Unknown
===================================

I become confused!!!


9 комментариев

salam DavodAmirajam
khoshhalam ye irani inja hast ke kar doroste
dadash age lotf koni komakam koni mamnoon misham
in flash amanat dastam bud ke injouri shod
1-DO Not Use Smi Factory
2-Create Cd Room Not Good In Smi Try It (Phison 2251(famly))

3-download this «RecoverTool_V2.00.33_L1224» and click the recover
go to silicon power .com and in support download recovery tool
midonam peda nemikone chon irania inja ro ham kharab mikonan ongad link mizaran pas bia up kardam to 4share vasat

www.4shared.com/archive/orKerPHD/SM32X_Modifid__By_Davod_Amiraj.html
az mp estfade nakon fagat recover.exe
ba «RecoverTool_V2.00.33_L1224» va SiliconPower RecoveryTool (090C1000.zip) detect nashod.
ba «Dyna MPTool» va «SMI MPTool» va «SM32X_Modifid__By_Davod_Amiraj» javab nadad.
Is there any other way?
I finally repair it with test mode is mentioned in flashboot.ru/flash_recovery/2013/10/17/silicon_power_recovery.html

Flash had pid/vid = 090C/1000. after test mode and appear drive letter, pid/vid became 090C/3000
and I perform flashing with Dyna MPTool (Star_SM3257ENAA_M0906).

Thnx.
Thanks all Friends on FlashBoot specially DavodAmirajam.

Оставить комментарий

Имя: