ok in final
we undrstand crystal controler pcb «2232-2233-2238» is same and we can use 1channel «2237-2239»
free crystal same model is «2260-2250-2261-2267-2268»
— in alcor all version pcb is mach
example you can change au6986 by au6998sn
you dont need «n»version install crystal
— in ite also 1165-1167-1167b-1169-1176 is same
— in smi like 2 model
crystal need (3255-3254-325ac-- is same)
free crystall model (3257-3257en-enba -enlt is same
also i have team group flash 2gb phison 2251-38 and some emmc nand 2gb
why team group used 4channel controller for 2GB .i cant undrstand
and pcb is un un usabled
becuase just emmc and dont have a tsop 48 pin
so i extract the controler from PCB
Да, я знаю что флэшка левая. Невозможно купить флэшку на 128Gb за 10 или 15 доларов. Спасибо за информацию на счет вычисления производителя с помощью id.
Yes, I know it is fake. It is impossible to by a true 128Gb flash drive for 10 or 15 dollars. Thanks for the info about the brand detection by id.
К сожалению не возможно посмотреть точную маркировку контролера и памяти так как она литая, так что мне пришлось попытатся разными версиями програм от Alcor пока нашел одну которая сработала для этой флэшки.
Unfortunaly as you can see it is not possible to see the controller and memory brand on that flash, so I had to try many version of programs from Alcor until found one that worked for me.
this is mp.ini
[PenDriveMP]
IC Type=PS2251-07
[Parameter Mark]
Parameter Type=F1_MP_21
[Customize Info]
USB VID=0x13FE
USB PID=0x5500
String Product Name=USB DISK 3.0
Inquiry Version=PMAP
[Configuration]
Reset Serial Number=0
Preformat Target Capacity=14500
[TestItemOption]
Do Preformat Test=1
[Extra]
Mode=3
[Misc]
Volume Label=USB DISK
Burner Erase All=1
Wafer Erase All=1
set1667=0x00
[Advance]
FC1=0xFF
FC2=0x01
CheckUSBConnectorType=0x22
[Firmware]
ISP=1
Burner File=C:\Documents and Settings\Administrator\My Documents\New Folder\BN07V502TAW.BIN
Firmware Name=C:\Documents and Settings\Administrator\My Documents\New Folder\FW07V50253TW.BIN
have a you know phison for ed3 14.4G? ok
in preformat i do same
have FW07V50253TW.BIN
i open log file
this file for ED3 tlc
look that
this log file some asshole think can pass this firmware for ed3
— MP\F1\AFD6\
MP_7f00_05.03.0a,17-5-2016 15:33:42s, Drive: G,R/W= 0%,Test Time:-130851, Time taken: 225.5 seconds, Capacity: 65536, Serial Number: 7F00651FA1AFD600,7F00651F84AFD601, Flash Number: 1,UIDeviceIndex=3,
Firmware Version: 5.02.53, Status: PASS, ISP Mode: 0x18, [CS]:0x791F2CA1
in tera copy up to 22 mb
i test in win xp 32bit
ok in final
we undrstand crystal controler pcb «2232-2233-2238» is same and we can use 1channel «2237-2239»
free crystal same model is «2260-2250-2261-2267-2268»
— in alcor all version pcb is mach
example you can change au6986 by au6998sn
you dont need «n»version install crystal
— in ite also 1165-1167-1167b-1169-1176 is same
— in smi like 2 model
crystal need (3255-3254-325ac-- is same)
free crystall model (3257-3257en-enba -enlt is same
good luck…
mpal 3.63+fw 2.06.10 (some people write firmware as FW38FF01V30610M.BIN but real is FW38FF01V2
controller pin is so small
i remove the Between connection with wire
in last picture from flash extractor used 2233 and t58nvg8d2ela20 *2 (used pcb for 64GB )
so lets start…
extract old tdk for used flash board
for undrstand is pcb support dual channel or interleaved?
finaly found in flash extractor
i loking for Good Flash Board
in phison site say 2251-38,2251-33,2251-32 is pin to pin Compatible
why team group used 4channel controller for 2GB .i cant undrstand
and pcb is un un usabled
becuase just emmc and dont have a tsop 48 pin
so i extract the controler from PCB
one from taiwan
Yes, I know it is fake. It is impossible to by a true 128Gb flash drive for 10 or 15 dollars. Thanks for the info about the brand detection by id.
К сожалению не возможно посмотреть точную маркировку контролера и памяти так как она литая, так что мне пришлось попытатся разными версиями програм от Alcor пока нашел одну которая сработала для этой флэшки.
Unfortunaly as you can see it is not possible to see the controller and memory brand on that flash, so I had to try many version of programs from Alcor until found one that worked for me.
Успехов.
Good luck.