+0.62
Рейтинг
0.50
Сила

Davod

look other Files
File 146 Is MP.ini

Look that

[PenDriveMP]
IC Type=PS2251-03
[Parameter Mark]
Parameter Type=F1_MP_21
[Customize Info]
USB VID=0x13FE
USB PID=0x5200
String Product Name=Silicon-Power128
String Manufacturer Name=UFD 3.0
Inquiry Version=PMAP
[Configuration]
Reset Serial Number=0
File System 1=2
[TestItemOption]
Do Preformat Test=1
[Extra]
Mode=3
[Misc]
Volume Label=SP UFD U3
Burner Erase All=1
set1667=0x00
[Advance]
FC1=0xFF
FC2=0x01
CheckUSBConnectorType=0x22
[Firmware]
ISP=1
Burner File=BN.BIN
Firmware Name=FW.BIN
 
Run Resorce Tuner And Open the Phison225103.exe

in EXterApp(this Mean Extrnal Applocation) have same file

I Save All And open one by one by note pad And Extract it
1-Download Sp Downloader From Silicon-power.com-Support -Download -Recovery

2-Spdownloader Detect 13fe 5200 and Download the Phison225103.exe

3-Download the Resource Tuner for Extract the Exe File
old sony and team group use skymedi 6213

SK6213 PDT 20100209A Maxell
fc alwayes for downgraed nand

in fc mptool ecc=0 capacity optimeze
password is 123456
SB8= USED IN MLC
IN SANDISK NAND WE MUST 2 OR MORE TIME ERASE ALL +55AA

SANDISK NAND TABLE IS VERY BAD AND VERY EASY TO LOSE MBR AND CAPACITY

I ALWAYES SAY I HATE SANDISK
FOR 19NM TLC =ECC 48
FOR 24 OR 19NM MLC ECC 30

FOR (5D2F)MLC (TC58NVG5D2FTA10,TH58NVG6D2FTA20) 15 BIT ECC

FOR SUMSONG TOGGLE TLC 48 BIT ECC

FOR L63 (I29F32G08AMD2,MT29F32G08CFAAA) 12 BIT ECC

NOTE:

ALWAYES IN TLC MORE THAN MLC USED ECC (BECUASE TLC DATA SAVED IN TRIPLE CELOL)
INSTALL OTHER SANDISK ON PHISON 2267

IN UP TOOL CLEAN ALL

CAPACITY OPTIMIZE
FULL SCAN ONLY

TEST YOUR MEMORY SAFE OR NOT?

هیتر کشی بد انجام دادی اثرات گرما زیاد رو شاسی بدنه دیده میشه
نند ساندیسک به شدت به حرارت حساسه و زود خراب میشه

مموری باقی مونده رو رو فیزون 2267 امتحان کن
اگه سالم بود یه صفحه جدید واسه مشکلت ایجاد کن قدم به قدم کمک میکنمت
FOR 1 OR 2 TIME ERASE ALL BLOCK

AFTER ERASE REPLUG AGAIN AND DO MP
Capacity optimize
In dynaa mp toool right click click erase all
After erase all replug flash
Go setting
Low level
Ecc 30
Auto 2plane +bin 1
no hasan sandisk (6d2h) 24nm Mlc 8k

in dyna downgraded tools i cant retrun any file

this firmware in downgraded mp tools

capacity optimize

low level
ecc =30

in downgraded flash is very danger to copy important file
good luck
you must just erase old Firmware by Uptool

we use Uptool For erase old Firmware

90 Cob Flash is normal

so must be firmware in Mpall

for 2251-07 use mpall 3.72 and we have firmware for 2207 1.02.10 1.1.53
2251-03 2251-01 2251-03 2251-07 cob(chip on board ) or normal PCB

To Get the Rom Code Mode (Skip From flash Hang) connect GNd to Led + side
no sandisk nand not fake but havent qualiy